Quick Answer: What’S Wrong With A Dryer When It Doesn’T Get Hot?

What’s wrong with a gas dryer when it doesn’t get hot?

If your gas dryer won’t heat, several things could be keeping it from operating normally.

The dryer could have a broken flame sensor, gas valve coils, high-limit thermostat, operating thermostat, thermal cut-off fuse, thermal fuse, igniter or timer..

How hard is it to replace a heating element in a dryer?

Replacing it isn’t a difficult task, but it does involve removing the back cover of the dryer. Before you do that, you have to be very sure that the power is off. Before replacing the element, check the continuity of the thermal fuse, because if it’s blown, you probably won’t have to replace the element.

Where is the thermal fuse located?

Once a replacement has been retrieved, start by unplugging your dryer and removing the back panel. The thermal fuse will be located somewhere by the exhaust vent on your dryer. You will be able to visually identify it by the two wires connecting to it.

What does a thermal fuse look like?

Thermal fuse shapes and sizes vary. Some are made from plastic; others are metal. Look for a small device about the size of a quarter to about 2 inches long, mounted directly on top of the exhaust duct. A thermal fuse has two wires connected to it.

How do you know if the heating element is bad in my dryer?

If your dryer takes longer than usual to dry your clothes, or the air in the dryer never heats, your heating element might be bad. You can test your heating element to determine whether you need to replace it. Unplug your dryer from the utility room wall outlet.

What causes heating element to go out in dryer?

It consists of an uninsulated metal conductor and when an electric current passes through it, its resistance to the flow of electricity makes it heat up. … Among the conditions that can cause elevated temperatures are insufficient airflow in the element compartment, failure of safety devices and a power surge.

How do I know if my thermal fuse is blown?

How to Tell if a Thermal Fuse is BlownUnplug your dryer and ensure it is no longer connected to the gas or electric.Locate the thermal fuse, as above.Disconnect the thermal fuse from the wires.Test the fuse with a multimeter.If the needle on your multimeter does not move, your thermal fuse is blow.

Can a clogged dryer vent cause no heat?

Blocked venting This is the most common cause of a dryer not heating. To check if your venting is clogged, start a timed dry on high heat. Go to the exhaust vent outside and use your hand to verify that the air is very warm and exiting at a decent flow.

How do I reset my thermal fuse?

Before replacing the thermal fuse again, try these steps: Unplug the dryer to disconnect electrical power….How do you change a thermal fuse on a dryer?Shut off the power. … Remove the back panel. … Remove the fuse.Install the new thermal fuse.Reattach the back panel.Plug in the dryer.More items…•

What would cause my dryer not to start?

Common dryer issues include a faulty door switch or start switch and control problems such as a broken dryer timer or faulty electronic control board: Problems with the door switch can prevent the dryer from starting. … A blown thermal fuse often prevents an electric dryer from starting.

How much does it cost to fix a dryer that won’t heat?

Dryer Heating Element Cost For the cost of parts and labor, you should budget at least $170 to $280 for a new heating element. An appliance technician typically charges between $80 and $100 per hour for labor. This cost also includes a one-time service fee. Most technicians’ service fees span from $50 to $80.

Why doesn’t my Whirlpool dryer heat up?

The operating thermostat can cause your Whirlpool dryer to stop heating. To test this, disconnect power to the dryer and disconnect the two outside wires off the thermostat, next test for continuity with an ohmmeter. If it is open replace it.

Is it worth repairing a dryer?

If a dryer is relatively new (five years or less), having it repaired can extend its life that much longer and save money in the long run. … It can be worth spending $150 – $200 to repair a midrange or high-end dryer that’s less than three years old, for example.

Is there a reset button on a Whirlpool dryer?

If your Whirlpool dryer displays a “PF” error code, indicating a recent power failure, the dryer will need to be reset and restarted. This is done by pressing “Start” for a few seconds to restart the dryer. If the dryer does not restart automatically, select a new cycle and any options then press “Start” to begin.

Where is the reset button on a dryer?

There is no reset button on your dryer. I recommend locating the two (2) house circuit breakers dedicated for the dryer and reset both circuit breakers by flipping them both OFF and ON 2-3 times and then check to see if the dryer will start.